Twitter

 





Система Orphus

Software for Renault cars

renaultSoftware for Renault cars allows you to perform adaptation of the keys, cards, writing and reading engine control units in Renault cars.

Software for Renault cars has the following functions:

 

  • Allows you to calculate the access code (PIN, login) based on the tag in the key or on label in the documents supplied with the car. This code is required for adaptation of the IR remote transponder and emergency engine start. Read more about this feature, you can here: RENAULT immobiliser pin-code calculator
Renault pin code calculator
 
  • For cars with infrared transponder Renault Megane, Renault Scenic, Renault Laguna is possible to generate the data needed to prepare the IR transponder for adapting to the car.
 Renault PIN code calculator
 
  • For cars with transponders based on RFID PCF793x (SILCA ID 33) can calculate data for the adaptation of the new transponder to the car based on the label in the key or a special label in the documents, which is important since many factory transponders often fail.
 
  • For the next generation of cars that use transponders Hitag 2 software allows you to learn new keys (cards) via diagnostic connector without an access code and to read the identifiers, the configuration and the crypto-data of already learned keys.
 
List of supported vehicles:
  • Renault Clio II (phase 2, phase 3)
  • Renault Espace IV (phase 1, phase 2)
  • Renault Kangoo Mux (phase 2)
  • Renault Laguna II (phase 1, phase 2)
  • Renault Logan
  • Renault Master (phase 2)
  • Renault Megane II (phase 1, phase 2)
  • Renault Scenic II
  • Renault Trafic II
  • Renault Vel Satis (phase 1, phase 2)
  • Renault Duster, Renault Sandero - will be added soon.

 
Renault cards learn
 
  • The software allows you to read and write FLASH and EEPROM in the engine control units (ECU): Siemens Sirius32, Siemens Sirius32N, Siemens Sirius34, Siemens Sirius35, Siemens EMS3132, Siemens EMS3134, BOSCH EDC15C3, BOSCH EDC15VM+ through the diagnostic connector OBD II
 Reading and witing engine control unit Siemens Sirius
 
Reading and writing EEPROM in ECU Siemens Sirius
 
Functions available for engine control units
 
Reading/writing the contents of FLASH (AM29F400 and AM29F200) and emulated EEPROM via diagnostic connector. Clearing immobiliser code for installing control unit to another car.
  • Siemens Sirius 32 - for the 16-valve engines can be programmed software that does not require immobilizer code.
  • Siemens Sirius 32N - for control units with immobilisers with K-Line or CAN.
  • Siemens Sirius 34
  • Siemens Sirius 35
  • Siemens EMS 3132 - for control units with immobilisers with K-Line or CAN.
  • Siemens EMS 3134

In case of damage of the contents of FLASH, program can restore the control unit via bootloader mode. (No other programmers required).

The software is tested on the following control units: S110030006C, S110030018D, S110030018D, S110030030A, S110030030B, S110030034A, S110030040A, S110030048B, S110030050B, S110030058A, S110030102D, S110030214C, S110038000A, S110110014N, S110110208N, S110110228D, S110110228D, S110130040A, S110137001A, S118301104A, S118303107A.

Reading and writing the contents of FLASH AM29F400 and EEPROM (5P08C3 and 24C04) via diagnostic connector. Odometer value correction:

  • BOSCH EDC15C3 - reading immobilizer code (adapting with UCH), which is a cryptographic key (ISN) for transponders Hitag 2 (For vehicles with Hitag 2).
  • BOSCH EDC15VM+

 

Siemens SID301 - support will be added soon.

Also there is the possibility of purchasing tuned firmwares for these controls units.
 
 

This software requires an adapter CEE-Team Special Interface.

Latest discussions